View LXDC2HL-G_9096760.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 july. 2015 lxdc2hl - g series micro dc - dc converter 1. features ? low emi noise and small footprint (5mm 2 ) using inductor - embedded ferrite substrate ? pfm/pwm automatic mode switching function ? smooth mode transient between pfm mode and pwm mode with low - ripple - voltage pfm mode ? 2% dc voltage accuracy over full load current range ? wide input voltage range : 2.3~5.5v ? fixed output voltage : 0.8v C 2. 5v (factory setting) ? internal soft start, overcurrent protection 2. description the lxdc2hl series is a low power step - down dcdc converter, which is suitable for a space - limited or a noise - sensitive application. the device utilizes an inductor - embedded ferrite substrate, and the substrate eliminates radiated emi noise and conduction n oise efficiently. by just putting input/output capacitors, it can be used as a ldo replacement. its low noise feature and easy to assembly feature assures reliable power supply quality. the device works in pfm mode at light load and it extends the batter y life. at heavy load, its control mode changes to pmw mode automatically and it keeps high efficiency using synchronous rectifying technology. the device keeps good output voltage accuracy even in pfm mode. it keeps 2% dc voltage accuracy over full curren t range, and shows very smooth mode transient between pfm mode and pwm mode. 3. typical application circuit lxdc2hl - g lxdc2hl enable vbat 10 uf gnd vin vout en vout
lxdc2hl - g series micro dc - dc converter 2 july. 2015 4. mechanical details 4 - 1 outline top view bottom view unit: mm mark dimension l 2.5 +/ - 0.2 w 2.0 +/ - 0.2 t 1.0 max a 0.85 +/ - 0.1 b 0.60 +/ - 0.1 c 0.15 +/ - 0.15 4 - 2. pin function pin symbol i/o description 1 vin input vin pin supplies current to the lxdc2hl internal regulator. side view
lxdc2hl - g series micro dc - dc converter 3 july. 2015 2 en input this is the on/off control pin of the device. connecting this pin to gnd keeps the device in shutdown mode. pulling this pin to vin enables the device with soft start. this pin must not be left floating and must be terminated. if this pin is left open, the device may be off around 100ma output. en=h: device on, en=l: device off 3 vout output regulated voltage output pin. apply output load between this pin and gnd. 4 gnd - ground pin 4 - 3. functional block diagram 5. ordering information part number output voltage device specific feature moq lxdc2hl10g - 301 1.0v standard type t/r, 3000pcs/r lxdc2hl11g - 306 1.1v standard type t/r, 3000pcs/r lxdc2hl12g - 302 1.2v standard type t/r, 3000pcs/r lxdc2hl13g - 441 1.3v standard type t/r, 3000pcs/r lxdc2hl15g - 303 1.5v standard type t/r, 3000pcs/r lxdc2hl18g - 304 1.8v standard type t/r, 3000pcs/r lxdc2hl25g - 341 2.5v standard type t/r, 3000pcs/r 6. electrical specification
lxdc2hl - g series micro dc - dc converter 4 july. 2015 6 - 1 absolute maximum ratings parameter symbol rating unit input voltage vin, en 6.3 v operating ambient temperature ta - 40 to +85 o c operating ic temperature t ic - 40 to +125 o c storage temperature t sto - 40 to +85 o c 6 - 2 electrical characteristics (ta=25 ) parameter symbol condition min. typ. max. unit input voltage v in 2.3 3.7 5.5 v uvlo voltage uvlo 1.0 1.4 1.8 v input leak current lin - off vin=3.7v, en=0v 0 2 ua output voltage accuracy vout vin - vout>1v lxdc2hl10g - 301 0.976 1.0 1.024 v lxdc2hl11g - 306 1.076 1.1 1.124 lxdc2hl12g - 302 1.176 1.2 1.224 lxdc2hl13g - 441 1.274 1.3 1.326 lxdc2hl15g - 303 1.47 1.5 1.53 lxdc2hl18g - 304 1.764 1.8 1.836 vin - vout>0.7v lxdc2hl25g - 341 2.45 2.5 2.55 load current range iout lxdc2hl10g - 301 0 300 ma lxdc2hl11g - 306 0 250 lxdc2hl12g - 302 0 250 lxdc2hl13g - 441 0 250 lxdc2hl15g - 303 0 200 lxdc2hl18g - 304 0 200 lxdc2hl25g - 341 0 200 ripple voltage vrpl vin=3.7v, iout=50ma, bw=100mhz lxdc2hl10g - 301 15 mvpp lxdc2hl11g - 306 15 lxdc2hl12g - 302 15 lxdc2hl13g - 441 15 lxdc2hl15g - 303 15 lxdc2hl18g - 304 15
lxdc2hl - g series micro dc - dc converter 5 july. 2015 lxdc2hl25g - 341 15 efficiency eff vin=3.7v, iout=100ma lxdc2hl10g - 301 80 % lxdc2hl11g - 306 81 lxdc2hl12g - 302 82 lxdc2hl13g - 441 83 lxdc2hl15g - 303 85 lxdc2hl18g - 304 86 lxdc2hl25g - 341 90 en control voltage venh on ; enable 1.4 vin v venl off ; disable 0 0.25 v sw frequency fosc 1.2 mhz over current protection ocp lxdc2hl10g - 301 350 700 1350 ma lxdc2hl11g - 306 300 700 1350 lxdc2hl12g - 302 300 700 1350 lxdc2hl13g - 441 300 700 1350 lxdc2hl15g - 303 250 700 1350 lxdc2hl18g - 304 250 700 1350 lxdc2hl25g - 341 250 700 1350 if the over current event continues less than tlatch, auto - recovery. if the over current event continues more than tlatch, latch - up. restart by toggling en voltage or vin voltage tlatch latch - up mask time @vout=0.8 vnom 20 usec start - up time ton 0.25 msec (*1) external capacitors (cout:10uf) shall be placed near the module in order to proper operation. (*2)the above characteristics are tested using the test circuit on section 8.
lxdc2hl - g series micro dc - dc converter 6 july. 2015 6 - 3 thermal and current de - rating information the following figures show the power dissipation and temperature rise characteristics. these data are measured on muratas evaluation board of this device at no air - flow condition. the output current of the device may need to be de - rated if it is operated in a high ambient temperature or in a continuous power delivering application. the amount of current de - rating is highly dependent on the env ironmental thermal conditions, i.e. pcb design, nearby components or effective air flows. care should especially be taken in applications where the device temperature exceeds 85 o c. the ic temperature of the device must be kept lower than the maximum rating of 125 o c. it is generally recommended to take an appropriate de - rating to ic temperature for a reliable operation. a general de - rating for the temperature of semiconductor is 80%. mlcc capacitors reliability and the lifetime is also dependant on temperature and applied voltage stress. higher temperature and/or higher voltage cause shorter lifetime of mlcc, and the degradation can be described by the arrhenius model. the most cr itical parameter of the degradation is ir (insulation resistance). the below figure shows mlccs b1 life based on a failure rate reaching 1%. it should be noted that wear - out mechanisms in mlcc capacitor is not reversible but cumulative over time. 0 10 20 30 40 50 60 70 80 100 150 200 0 50 iout [ma] io - loss characteristics (vin=3.7v) 0 1 2 3 4 5 6 0 20 40 60 80 power dissipation[mw] loss - t characteristics (vin=3.7v)
lxdc2hl - g series micro dc - dc converter 7 july. 2015 the following steps should be taken before the design fix of users set for reliable operation. 1. the ambient temperature of the device should be kept below 85 o c 2. the ic temperature should be measured on the worst condition of each application. the te mperature must be kept below 125 o c. an appropriate de - rating of temperature and/or output current should be taken. 3. the mlcc temperature should be measured on the worst condition of each application. considering the above figure, it should be checked if t he expected b1 life of mlcc is acceptable or not. 7. detailed description pfm/pwm mode if the load current decreases, the converter will enter pfm mode automatically. in pfm mode, the device operates in discontinuous current mode with a sporadic one switching pulse to keep high efficiency at light load. the device uses constant on time contr ol in pfm operation, which produces a low ripple voltage and accurate output voltage compared with other pfm architectures. because of the architecture, dc output voltage can be kept within +/ - 2% range of the nominal voltage and the output ripple voltage i n pfm mode can be reduced by just increasing output capacitor. the transition between pfm and pwm is also seamless and smooth. the transition current between pfm and pwm is depend on vin, vout and other factors, but the ballpark threshold is about 100 - 2 00ma pfm mode at light load pwm mode at heavy load nominal output voltage
lxdc2hl - g series micro dc - dc converter 8 july. 2015 uvlo (under voltage lock out) the input voltage (vin) must reach or exceed the uvlo voltage (1.4vtyp) before the device begins the start up sequence even when en pin kept high. uvlo function keeps away of an unstable operation at low vin range soft start the device has an internal soft - start function that limits the inrush current during start - up. the soft - start system progressively increases the switching on - time from a minimum pulse - width to that of normal operation. because of the function, the output voltage increases gradually from zero to nominal voltage at start - up event. the nominal soft - start time is 0.25msec. if you prefer a faster soft - start time, please contact murata representative. enable the device starts operation when en is set high and starts up with soft star t. for proper operation, the en pin must be terminated to logic high and must not be left floating. if the pin is left open, the device may operate at light load but will not work at heavy load. pulling the en pin to logic low forces the device shutdown. the device does not have a discharge function when it turns off. if you prefer a discharge function, please contact murata representative. 100% duty cycle operation the device can operate 100% duty cycle mode, in which high - side switch is constantly turned on, thereby providing a low input - to - output voltage difference. when vin and vout becomes close and the duty gets close to 100%, the switching pulse will skip the nominal switching period and the output voltage ripple may be larger than other condi tion. it should be noted that this condition does not mean a failure of the device. over current protection when the output current reaches the ocp threshold, the device narrows the switching duty and decrease the output voltage. if the ocp event is removed within the mask time (20usec typ), the output voltage recovers to the nominal value automatically. if the ocp event continues over the mask time, the device will shutdown. after it is shut down, it can be restarted by toggling the vin or en voltage.
lxdc2hl - g series micro dc - dc converter 9 july. 2015 8. test circuit cout : 10uf/6.3v (grm155r60j106m) lxdc2hl - g
lxdc2hl - g series micro dc - dc converter 10 july. 2015 9. measureme nt data micro dc - dc converter evaluation board (p2lx0244) the enable switch has three positions. 1. when it is toggled to on side, the device starts operation. 2. when it is toggled to off side, the device stop operation and keep shut down status. 3. when it is set to middle of on and off, the en pin becomes floated and can be applied an external voltage through the en terminal pin on the evb. if you dont apply external voltage to en pin, the enable switch should not to be set to the middle positi on. the 47uf capacitor is for the evaluation kit only, and has been added to compensate for the long test cables. typical measurement data (reference purpose only) (ta=25 ) efficiency ? vin=3.7v,vout=1.0v ? vin=3.7v,vout=1.2v measurement setup enable sw vin vin_s gnd vout_s a a vout gnd_s v gnd_s load v gnd
lxdc2hl - g series micro dc - dc converter 11 july. 2015 ? vin=3.7v,vout=1.5v ? vin=3.7v,vout=1.8v ? vin=3.7v,vout=2.5v load regulation ? vin=3.7v,vout=1.0v ? vin=3.7v,vout=1.2v 60 65 70 75 80 85 90 95 100 1 10 100 1000 iout [ma] 60 65 70 75 80 85 90 95 100 1 10 100 1000 iout [ma] 60 65 70 75 80 85 90 95 100 1 10 100 1000 iout [ma] 60 65 70 75 80 85 90 95 100 1 10 100 1000 iout [ma] 60 65 70 75 80 85 90 95 100 1 10 100 1000 iout [ma]
lxdc2hl - g series micro dc - dc converter 12 july. 2015 ? vin=3.7v,vout=1.5v ? vin=3.7v,vout=1.8v ? vin=3.7v,vout=2.5v ripple voltage ? vin=3.7v,vout=1.0v ? vin=3.7v,vout=1.2v 0.98 0.99 1 1.01 1.02 250 300 150 0 50 100 200 iout [ma] 1.176 1.188 1.2 1.212 1.224 0 50 100 150 200 250 iout [ma] 1.47 1.485 1.5 1.515 1.53 50 0 100 150 200 iout [ma] 1.764 1.782 1.8 1.818 1.836 0 50 100 150 200 iout [ma] 2.45 2.475 2.5 2.525 2.55 0 50 100 150 200 iout [ma]
lxdc2hl - g series micro dc - dc converter 13 july. 2015 ? vin=3.7v,vout=1.5v ? vin=3.7v,vout=1.8v ? vin=3.7v,vout=2.5v load transient response ? vin=3.7v, vout=1.8v v,vout=1.1v 3.7 0 10 20 30 40 50 200 250 300 50 0 100 150 iout [ma] 0 10 20 30 40 50 50 100 150 200 250 0 iout [ma] 0 10 20 30 40 50 0 50 100 150 200 iout [ma] 0 10 20 30 40 50 0 50 100 150 200 iout [ma] 0 10 20 30 40 50 0 50 100 150 200 iout [ma]
lxdc2hl - g series micro dc - dc converter 14 july. 2015 10.reliability tests no. items specifications test methods qty result (ng) 1 vibration resistance appearance : no severe damages solder specimens on the testing jig (glass fluorine boards) shown in appended fig.1 by a pb free solder. the soldering shall be done either by iron or reflow and be conducted with care so that the soldering is uniform a nd free of defect such as by heat shock. frequency : 10~2000 hz acceleration : 196 m/s 2 direction : x,y,z 3 axis period : 2 h on each direction total 6 h. 18 g (0) 2 deflection solder specimens on the testing jig (glass epoxy boards) shown in appended fig.2 by a pb free solder. the soldering shall be done either by iron or reflow and be conducted with care so that the soldering is uniform and free of defect such as by heat shock. deflection : 1.6mm 18 g (0) io=200ma 192 mv
lxdc2hl - g series micro dc - dc converter 15 july. 2015 3 soldering strength (push strength) 9.8 n minimum solder specimens onto test jig shown below. apply pushing force at 0.5mm/s until electrode pads are peeled off or ceramics are broken. pushing force is applied to longitudinal direction. 18 g (0) 4 solderability of termination 75% of the terminations is to be soldered evenly and continuously. immerse specimens first an ethanol solution of rosin, then in a pb free solder solution for 30.5 sec. at 2455 c. preheat : 150 c, 60 sec. solder paste : sn - 3.0ag - 0.5cu flux : solution of ethanol and rosin (25 % rosin in weight proportion) 18 g (0) 5 resistance to soldering heat (reflow) appearance electrical specifications no severe damages satisfy specifications listed in paragraph 6 - 2. preheat temperature : 150 - 180 c preheat period : 90+/ - 30 sec. high temperature : 220 c high temp. period : 20sec. peak temperature : 260+5/ - 0 c specimens are soldered twice with the above condition, and then kept in room condition for 24 h before measurements. 18 g (0) no. items specifications test methods qty result (ng) 6 high temp. exposure appearance no severe damages temperature 852 period 1000+48/ - 0 h room condition 2 24h 18 g (0) 7 temperature cycle condition 100 cycles in the following table step temp(c) time(min) 1 min. operating temp.+0/ - 3 303 2 max. operating temp.+3/ - 0 303 18 g (0) 8 humidity (steady state) temperature 852 humidity 80 90%rh period 1000+48/ - 0 h room condition 2 24h 18 g (0) pushing direction jig specimen
lxdc2hl - g series micro dc - dc converter 16 july. 2015 9 low temp. exposure electrical specifications satisfy specifications listed in paragraph 6 - 2. temperature - 402 period 1000+48/ - 0 h room condition 2 24h 18 g (0) 10 esd(machine model) c 200pf r 0 test voltage +/ - 100v number of electric discharges 1 5 g (0) 11 esd(human body model) c 100pf r 1500 test voltage +/ - 1000v number of electric discharges 1 5 g (0) fig.1 land pattern unit mm ? reference purpose only . fig.2 testing board symbol dimensions a 0.85 b 0.60 c 0.5 d 0.2
lxdc2hl - g series micro dc - dc converter 17 july. 2015 unit mm land pattern is same as figure1 glass - fluorine board t 1.6mm copper thickness over 35 m m mounted situation unit mm test method unit mm 11. tape and reel packing 1 dimensions of tape (plastic tape) unit: mm 45 45 ? device
lxdc2hl - g series micro dc - dc converter 18 july. 2015 2 dimensions of reel unit: mm 13.0 1.4 ( 9.0 ) 13 0.2 60 2 0.5 180
lxdc2hl - g series micro dc - dc converter 19 july. 2015 3 taping diagrams [1] feeding hole : as specified in (1) [2] hole for chip : as specified in (1) cover tape : 50um in thickness [3] [4] base tape : as specified in (1) [1] [2] [3] [3] [4] feeding hole chip feeding direction
lxdc2hl - g series micro dc - dc converter 20 july. 2015 symbol items ratings(mm) a no components at trailer min 160 b no components at leader min 100 c whole leader min 400 5 the tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled toward the user. 6 packaging unit: 3,000 pcs./ reel 7 material base tape plastic reel plastic antistatic coating for both base tape and reel 8 peeling of force 165 to 180 0.7 n max. ?`?` `?` 0.1~1.0 n cover tape base tape
lxdc2hl - g series micro dc - dc converter 21 july. 2015 notice 1. storage conditions: to avoid damaging the solderability of the external electrodes, be sure to observe the following points . - store products where the ambient temperature is 15 to 35 c and humidity 45 to 75% rh. (packing materials, in particular, may be deformed at the temperature over 40 c.) . - store products in non corrosive gas (cl 2 , nh 3 ,so 2 , no x , etc.). - stored products should be used within 6 months of receipt. solderability should be verified if this period is exceeded this product is applicable to msl1 (based on ipc/jedec j - std - 020 ) 2. handling conditions: be careful in handling or transporting the product. excessive stress or mechanical shock may damage the product because of the nature of ceramics structure. do not touch the product, especially the terminals, with bare hands. doing so may result in poor solderability. 3. standard pcb desi gn (land pattern and dimensions): all the ground terminals should be connected to ground patterns. furthermore, the ground pattern should be provided between in and out terminals. please refer to the specifications for the standard land dimensions. the recommended land pattern and dimensions are shown for a reference purpose only. electrical, mechanical and thermal characteristics of the product shall depend on the pattern design and material / thickness of the pcb. therefore, be sure to check t he product performance in the actual set. when using underfill materials, be sure to check the mechanical characteristics in the actual set. 4. soldering conditions: soldering is allowed up through 2 times. carefully perform preheating t less than 130 c. when products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 c. soldering must be carried out by the above mentioned conditions to prevent products from damage. contact murata before use if concerning other soldering conditions.
lxdc2hl - g series micro dc - dc converter 22 july. 2015 reflow soldering standard conditions (example) use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. 5. cleaning conditions: the product is not designed to be cleaned after soldering. 6. operational environment conditions: products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). therefore, pr oducts have no problems to be used under the similar conditions to the above - mentioned. however, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur . - in an atmosph ere containing corrosive gas ( cl 2, nh 3, so x, no x etc.). - in an atmosphere containing combustible and volatile gases. - in a dusty environment. - direct sunlight
lxdc2hl - g series micro dc - dc converter 23 july. 2015 - water splashing place. - humid place where water condenses. - in a freezing environment. if there are possibilities for products to be used under the preceding clause, consult with murata before actual use. if static electricity is added to this product, degradation and destruction may be produced. please use it after consideration enough so that neither static electricity nor excess voltage is added at the time of an assembly and measurement. if product malfunctions may result in serious damage, including that to human life, sufficient fail - safe measures must be taken, including the following: (1) installation of protection circuits or other protective device to improve system safety (2) installation of redundant circuits in the case of single - circuit failure 7. input power capacity: products shall be used in the input power capacity as specified in this specifications. inform murata beforehand, in case that the components are used beyond such input power capacity range . 8. limitation of applications: the products are designed and produced for application in ordinary electronic equipment (av equipment, oa equipment, telecommunication, etc). if the products are to be used in devices requiring extremely high reliability following the application listed be low, you should consult with the murata staff in advance. - aircraft equipment. - aerospace equipment - undersea equipment. - power plant control equipment. - medical equipment. - transportation equipment (vehicles, trains, ships, etc.). - automobile equipmen t which includes the genuine brand of car manufacture, car factory - installed option and dealer - installed option. - traffic signal equipment. - disaster prevention / crime prevention equipment. - data - procession equipment. - application which malfunction or op erational error may endanger human life and property of assets. - application which related to occurrence the serious damage - application of similar complexity and/ or reliability requirements to the applications listed in the above.
lxdc2hl - g series micro dc - dc converter 24 july. 2015 note: please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. product specifications are subject to change or our products in it may be discontinued without advance notice. this catalog is for reference only and not an official product specification document, therefore, please review and approve our official product specification before ordering this product. !

▲Up To Search▲

Price & Availability of LXDC2HL-G

	To Download LXDC2HL-G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .